Titanium VT1-00

Designation

Name The value
Designation GOST Cyrillic ВТ1-00
Designation GOST Latin BT1-00
Transliteration VT1-00
By chemical elements ВTe1-00

Description

Titanium VT1−00 is used: for the manufacture of semi-finished products (sheets, strips, foils, strips, plates, bars, rods, profiles, tubes, forgings and forged blanks) by the method of deformation, and also ingots; consumable electrode vacuum-arc remelting used as charge in the manufacture of shaped castings; lightly complex parts operating at temperatures from -253 to +150 °C; degassed titanium welding wire diameter 1,0−7,0 mm; superconducting niobium-titanium alloys.

Note

The material of the low strength, and titanium VT1−00, contains less impurities than VT1−0, has a lower strength and greater ductility. The strength properties of titanium can be increased by cold deformation but much reduced plastic properties. Reduced characteristics of plasticity are more pronounced than the increase of the strength characteristics, so that the cold deformation is not the best way to improve the properties of titanium. The disadvantages of titanium include high propensity to hydrogen embrittlement, and therefore the content of hydrogen should not exceed 0.008% in titanium VT1−00.

Standards

Name Code Standards
Non-ferrous metals, including rare, and their alloys В51 GOST 19807-91, OST 1 90000-70, OST 1 90013-81, OST 4.021.009-92, TU 1-5-132-78, TU 1-5-226-89
Sheets and strips В53 GOST 22178-76, GOST 23755-79, OST 1 90218-76, OST 1 90145-74, OST 1 90024-94, TU 1-5-111-73, TU 1-5-362-84
Tubes of non-ferrous metals and alloys В64 GOST 24890-81, OST 1 90050-72, OST 1 90051-79, OST 1 90065-72, OST 1 90050-92, OST 4.021.126-92, TU 14-3-1913-93
Bars В55 GOST 26492-85, OST 1 92020-82, OST 1 90266-86, OST 1 90173-75, OST 1 90107-73, OST 1 90006-86, TU 1-5-008-78
Welding and cutting metals. Soldering, riveting В05 OST 1 90015-77, TU 1-9-77-85, TU 1-9-922-82
Tape В54 OST 1 90027-71
Bars and shapes В52 OST 1 92051-76
Steel pipes and fittings to them В62 TU 14-3-161-73

Chemical composition

Standard C Si Fe N Al Ti O H
OST 1 90013-81 ≤0.05 ≤0.08 ≤0.15 ≤0.04 ≤0.3 Rest ≤0.1 ≤0.008
GOST 19807-91 ≤0.05 ≤0.08 ≤0.15 ≤0.04 - Rest ≤0.1 ≤0.008
OST 1 90015-77 ≤0.05 ≤0.08 ≤0.15 ≤0.04 ≤0.3 Rest ≤0.12 ≤0.008
Ti is the basis.
According to GOST 19807-91 and OST 1 90013-81 the total content of other impurities is ≤ 0.10%. The mass fraction of hydrogen is indicated for ingots. The mass fraction of aluminum is not more than 0.30%. The mass fraction of chromium and manganese should not exceed 0.15% (in total). The mass fraction of copper and nickel should not be more than 0.10% (in total), including nickel not more than 0.08%.
According to OST 1 90013-81 in the welding wire of technical grade VT1-00 grade, Al content is ≤ 0.20%, N ≤0.030%, O ≤ 0.12%, H ≤ 0.003%.

Mechanical properties

Section, mm sT|s0,2, MPa σU, MPa d5, % d y, % KCU, kJ/m2 HB, MPa
The billet according to TU 1-5-132-78. Annealing
Образец 15х15 ≥216 294-441 ≥30 - ≥60 1520 -
Образец 15х15 ≥118 ≥176 - - - - -
Sheet metal in delivery condition after annealing (samples across the direction of rolling)
0.3-1.8 - 294-441 ≥30 - - - -
1.8-6 - 294-441 ≥25 - - - -
6-10.5 - 294-441 ≥20 - - - -
Plate in the delivery condition according to GOST 23755-79. Without heat treatment (samples transverse)
11-60 - 295-490 - ≥14 ≥28 - -
60-150 - 295-490 - ≥11 ≥25 - -
Plate on OST 1 90024-94 in the delivery condition. Samples heat-treated (transverse)
11-60 - 290-440 - ≥14 ≥30 - -
60-150 - 290-440 - ≥11 ≥25 - -
Forgings weighing up to 200 kg after annealing (indicated by the direction of fillet samples)
101-150 - 265-440 ≥21 - ≥36 ≥588 116-149
151-250 - 265-440 ≥19 - ≥34 ≥588 116-149
100 - 294-440 ≥25 - ≥55 ≥1177 116-149
Wire welding degassed on the other 1-9-922-82
1-7 - 294-471 ≥30 - - - -
The welding wire in degassed and etched condition of supply for OST 1 90015-77
1-7 - ≤471 - ≥15 - - -
Bars hot rolled autogenie ordinary quality GOST 26492-85 (longitudinal samples)
10-12 - ≥295 ≥20 - ≥50 - -
100-150 - ≥265 ≥20 - ≥40 ≥588 -
12-100 - ≥295 ≥20 - ≥50 ≥980 -
Bars hot rolled autogenie high-quality according to GOST 26492-85 (longitudinal samples)
10-12 - 295-440 ≥25 - ≥55 - -
100-150 - 265-440 ≥24 - ≥42 ≥588 -
12-100 - 295-440 ≥25 - ≥55 ≥1176 -
Bars and rods, hot-rolled. Annealing (indicates the direction and place of cutting out of samples)
≥110 - 265-440 ≥24 - ≥42 ≥588 116-149
65-100 - 295-440 ≥25 - ≥55 ≥1176 116-149
10-60 - 294-441 ≥25 - ≥55 ≥1176 116-149
Forged square bars and round after annealing (indicated by the direction of fillet samples)
≤150 - 265-441 ≥21 - ≥36 ≥588 116-149
151-250 - 265-441 ≥19 - ≥34 ≥588 116-149
- 265-441 ≥22 - ≥45 ≥882 116-149
The pressed bars for OST 1 92020-82. Annealing. The longitudinal samples
100 - 294-441 - ≥25 ≥55 1177 -
Tubes rolled and drawn, otoczenie etched surface with an outer diameter of 6.0-62,0 mm; welded without heat treatment the outer diameter of 25.0-102,0 mm; cold drawn autogenie an outer diameter of 8,0-30,0 mm
- 300-450 ≥20 - - - -
Welded pipe groups A (annealed) and B (without t/o) in the delivery state according to GOST 24890-81 (samples, in cross-section is specified outside diameter)
38-102 - 392-539 ≥15 - - - -

Description mechanical marks

Name Description
sT|s0,2 Yield strength or limit of proportionality with a tolerance for residual deformation of 0.2%
σU Limit short-term strength
d5 Elongation after rupture
d Elongation after rupture
y The relative narrowing
KCU Toughness
HB Brinell hardness number

Physical characteristics

Temperature Е, HPa r, kg/m3 l, W/(m · °C)
20 112 4505 1885

A description of the physical symbols

Name Description
Е The normal elasticity modulus
r Density
l Coefficient of thermal conductivity
R UD. the resistivity
С Specific heat

Technological properties

Name The value
Weldability Without restrictions.